Command count: (Command ID) Command description
1: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M103 - extruder off"
2: (137) Disable A stepper motors
3: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M73 - start build"
4: (153) Start build notification, steps 0, name "lint"
5: (150) Set build percentage 0%, reserved 0
6: (134) Switch to Tool 0
7: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G0 - rapid move"
8: (139) Absolute move to (889, 889, 4000, -96, 0) with DDA 269
9: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G0 - rapid move-f"
10: (155) Move to (-889, -889, -4000, -96, 0), DDA rate 3849, A, B relative, distance 34.641018 mm, feedrate*64 1066 steps/s
11: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G1 - coord move"
12: (155) Move to (889, 889, 4000, -96, 0), DDA rate 3849, A, B relative, distance 34.641018 mm, feedrate*64 1066 steps/s
13: (150) Set build percentage 1%, reserved 0
14: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G1 - coord move-f"
15: (155) Move to (889, 889, 4000, -97, 0), DDA rate 2560, A, B relative, distance 1.000000 mm, feedrate*64 1706 steps/s
16: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G4 - dwell"
17: (133) Dwell for 1000 milliseconds
18: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G10 - set offsets"
19: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G21 - metric units"
20: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G28 - home to max"
21: (132) Home maximum on X, Y, feedrate 382 us/step, timeout 20 s
22: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G54 - use G10 P1"
23: (139) Absolute move to (889, 889, 4000, -578, 0) with DDA 337
24: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G55 - use G10 P2"
25: (155) Move to (1778, 1778, 8000, -97, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
26: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G56 - use G10 P3"
27: (155) Move to (2667, 2667, 12000, -96, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
28: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G57 - use G10 P4"
29: (155) Move to (3556, 3556, 16000, -96, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
30: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G58 - use G10 P5"
31: (155) Move to (4444, 4444, 20000, -96, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
32: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G59 - use G10 P6"
33: (155) Move to (5333, 5333, 24000, -97, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
34: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G53 - machine zero"
35: (155) Move to (0, 0, 0, -96, 0), DDA rate 7698, A, B relative, distance 103.923050 mm, feedrate*64 2133 steps/s
36: (150) Set build percentage 2%, reserved 0
37: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G91 - relative"
38: (155) Move to (889, 889, 4000, 1059, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
39: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G90 - absolute"
40: (155) Move to (0, 0, 0, -1252, 0), DDA rate 7698, A, B relative, distance 17.320509 mm, feedrate*64 2133 steps/s
41: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G92 - define pos"
42: (140) Define position as (2667, 2667, 12000, 0, 0)
43: (155) Move to (0, 0, 0, 0, 0), DDA rate 7698, A, B relative, distance 51.961525 mm, feedrate*64 2133 steps/s
44: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G130 - set pots"
45: (145) Set X axis digipot to 20
46: (145) Set Y axis digipot to 20
47: (145) Set Z axis digipot to 20
48: (145) Set A axis digipot to 20
49: (145) Set B axis digipot to 20
50: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G130 - home xy max"
51: (132) Home maximum on X, Y, feedrate 382 us/step, timeout 20 s
52: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "G130 - home xy min"
53: (131) Home minimum on Z, feedrate 136 us/step, timeout 20 s
54: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M104 - set temp"
55: (136) Tool 0: (3) Set target temperature to 230 C
56: (150) Set build percentage 19%, reserved 0
57: (136) Tool 1: (3) Set target temperature to 230 C
58: (150) Set build percentage 36%, reserved 0
59: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M6 - wait for tool"
60: (135) Wait until Tool 0 is ready, 100 ms between polls, 65535 s timeout
61: (134) Switch to Tool 1
62: (135) Wait until Tool 1 is ready, 100 ms between polls, 65535 s timeout
63: (135) Wait until Tool 1 is ready, 100 ms between polls, 65535 s timeout
64: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M17 - steppers on"
65: (137) Enable X, Y, Z, A, B stepper motors
66: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M18 - steppers off"
67: (137) Disable X, Y, Z, A, B stepper motors
68: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "T0 - tool change"
69: (134) Switch to Tool 0
70: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "T1 - tool change"
71: (134) Switch to Tool 1
72: (149) Display message, options 0x00, position (0, 0), timeout 0 s, message "This is a really lar"
73: (149) Display message, options 0x01, position (0, 0), timeout 0 s, message "ge message that will"
74: (149) Display message, options 0x01, position (0, 0), timeout 0 s, message " take up quite a few"
75: (149) Display message, options 0x03, position (0, 0), timeout 20 s, message " rows to display on "
76: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M71 - wait for input"
77: (149) Display message, options 0x06, position (0, 0), timeout 0 s, message "Press the M Button"
78: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M72 - play song"
79: (151) Queue song 0
80: (151) Queue song 1
81: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M73 - progress"
82: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M101 - extruder on-f"
83: (137) Enable B stepper motors
84: (137) Enable A stepper motors
85: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M102 - extruder on-r"
86: (137) Enable B stepper motors
87: (137) Enable A stepper motors
88: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M103 - extruder off"
89: (137) Disable B stepper motors
90: (137) Disable A stepper motors
91: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M104 - set temp"
92: (136) Tool 1: (3) Set target temperature to 240 C
93: (136) Tool 0: (3) Set target temperature to 230 C
94: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M108 - set rpm"
95: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M109 - hbp temp"
96: (136) Tool 0: (3) Set target temperature to 110 C
97: (135) Wait until Tool 0 is ready, 100 ms between polls, 65535 s timeout
98: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M126 - blower on"
99: (136) Tool 0: (13) Toggle blower fan 1
100: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M127 - blower off"
101: (136) Tool 0: (13) Toggle blower fan 0
102: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M131 - store EEPROM"
103: (143) Store home position for X, Y, Z, A, B
104: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M132 - load EEPROM"
105: (144) Recall home position for X, Y, Z, A, B
106: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M140 - hbp temp"
107: (136) Tool 0: (31) Set build platform temperature to 100 C
108: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M300 - set beep"
109: (147) Set buzzer frequency 4000, duration 100 ms, effect 0
110: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M320 - acc on"
111: (156) Set segment acceleration on
112: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M21 - acc off"
113: (156) Set segment acceleration off
114: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M322 - pause@z"
115: (158) Pause @ Z position 10.000000
116: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M420 - set LED"
117: (146) Set RGB LED (0xff, 0x00, 0x00), blink rate 0, effect 0
118: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "T1 - set tool"
119: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "T0 - set tool"
120: (134) Switch to Tool 0
121: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "M73 - end build"
122: (150) Set build percentage 100%, reserved 0
123: (154) End build notification, options 0x00
124: (149) Display message, options 0x02, position (0, 0), timeout 0 s, message "after the end"
125: (8) Pause
EOF
